Page 1 of 9 Next ››
  • 4x4 Front Axle Ends (set of 2)

    Make a custom front axle for your 4x4 project. Use these axle ends and 0.125 diameter brass tube to make your axle the width you need. Combine them with the Dana 44 rear differential. They feature open u-joint detail, brake discs and calipers, and tie rod attachment points. An ample wheel mounting boss is provided to mount to your wheels.

    $7.00
  • 4x4 Front Axle Kit

    You'll have tremendous design flexibility with Calnaga's 4x4 Axle Kit. You get accurate axle ends, radius rods, Dana 44 differential, and an ample length of axle tube. Locate the differential left, right, or wherever you need it! Adjust the wheelbase radius rod width and pinion angle to suit your project. Have fun scratch-building, not head-scratching.

    $15.00
  • 4x4 Radius Rods (Set of 2)

    The design of these radius rods is loosely based on a full scale Ford Econoline 4x4 conversion known as a Quadravan. They are drilled to accept 0.125 tube or rod, so you can combine them with our 4x4 Front Axle Ends and the Dana 44 Differential to make a super-detailed front axle that fits your 4x4 just right.. They have a coil spring mounting pad and bolt head detail. The end of the rod has pilot holes to drill for the bushing rod ends.

    $7.00
  • Accessory Display Set

    Add interest and realism to your display or diorama with Calnaga Display Accessories. These items are commonly found in the garage, pit area, or campsite. Put them in the back of your truck or van for a realistic load. The set includes one of each: Sleeping Bag, Bed Roll, Large Gear Bag, Small Gear Bag, Fuel Jug 10 gallon (1:25 scale) and Fuel Jug, 10 Gallon, (1:32 scale). (Parts shown include a paint and detail suggestion only. Your parts are delivered in plain white resin.)

    $12.50
  • Battery Box, Trunk Mount

    Properly executed trunk-mount battery applications use a marine battery box like this to collect fumes and vent them outside the interior. These are commonly seen on street machines, street rods and drag cars. Many drag cars have two of these for extra weight at the rear. The universal battery box includes several locations to locate the ground and "B+" wires.

    $2.00
  • Battery Set

    The problem with kit batteries is that they are injection molded, so they have that unrealistic taper called draft angle. Usually, they are hollow and don't even have six sides! These batteries are square, complete, and have detail that isn't possible with the injection molding process. Check the top post detail and side terminals. Four different batteries are included in the set: Universal maintenance-free battery with top posts and side terminals. Universal heavy duty battery with filler cap detail, top posts and side terminals. 60's vintage Autolite Sta-ful. This part has been corrected from the kit with six true sides, and molded in hold down detailm - Perfect for Ford muscle cars. Small car battery for OEM compacts and tuners. Includes molded in kit clamp detail.

    $5.00
  • Battery, Gel Cel, Group 34/78

    Optima gel cel batteries are the hot setup these days. This battery has label detail and accurate dimensions for the Group 34/78 size. The terminals will fit through Detailed photo-etch battery cable clamps. Nice touch, huh? Paint with a red top for hard starting drag race applications, and yellow top for race cars or street machines needing a high endurance deep cycle battery. Blue is for marine applications. Actual dimensions 0.400"L x 0.266'W x 0.330"H.

    $2.00
  • Bed Roll

    The bed roll is a little smaller than the sleeping bag and can also represent a rolled up blanket or tarp. Also works for a sleeping bag in 1:32 scale. Approximate dimensions: 0.42" diameter by 0.72" length. (Detail suggestion shown. Part is delivered in plain white resin)

    $2.50
  • Blower Manifold, Small Block Chevy

    This blower manifold has all the correct runner detail and gusseting. A lot more realistic than the typical trapezoid shaped piece of styrene you get in a kit. An excellent choice for diorama detail or if your engine is displayed with the valve covers off.

    $3.00
  • Blower Scoop, Crower 8-Port Injector

    The Crower 8-Port injector was introduced in 1968, but really gained prominence on Don Garlits' first rear-engine dragster in 1971. This injector was tricky to tune but found success with various teams along with Garlits including Don Prudhomme, Keeling and Clayton, "Jungle Jim" Liberman, Gordie Bonnin, and Gene Conway. It's a prominent detail you need to get right if building a replica. If you are doing a ficticious drag subject from the Seventies into the early Eighties, it will add some unique visual interest.

    $3.00
HomeOur MissionAbout UsStoreGalleryNewsPoliciesContact Us

Calnaga Castings
The Calnaga Store